FREE SHIPPING TO ANY FFL DEALER  |  15% OFF WITH CRYPTOCURRENCY PAYMENT

Choosing Scope Height for Your Remington Model 700

Selecting the correct scope height for a Remington Model 700 affects far more than appearance. Ring height influences cheek weld, eye alignment, bolt-handle clearance, objective-lens space, and the rifle’s overall balance. A scope mounted too low may contact the barrel, while one mounted too high can make a comfortable, repeatable shooting position difficult to achieve. Learn more about How Military Discounts Apply To Custom Or Special Order Firearms.

The right setup depends on the specific Model 700 configuration, scope dimensions, mounting system, and intended use. A compact hunting optic may fit in low rings, while a large long-range scope with a 50 mm objective usually needs more clearance. The goal is the lowest practical position that leaves adequate space and supports a natural sight picture.

Before installing anything, unload the rifle, remove the bolt when practical, and work in a safe direction. Confirm that the bases, rings, and optic are compatible with your receiver and scope tube diameter. A careful measurement before purchasing hardware is easier and less expensive than correcting a poorly fitted setup later.

Understand What Scope Height Means

Scope height generally describes the distance between the rifle’s bore axis and the centerline of the scope tube, although manufacturers may measure or label ring height differently. Some list the distance from the receiver or rail to the ring center, while others describe the clearance beneath the scope. Because these specifications are not completely standardized, compare measurements from the same manufacturer whenever possible.

Ring height is commonly described as low, medium, or high. Those terms are useful for browsing, but they are not precise enough by themselves. A “low” ring from one brand may be close to a “medium” ring from another. The scope’s outside diameter, the rifle’s barrel contour, and the thickness of the mounting base all affect the final position.

For a Model 700, consider the receiver profile, barrel diameter near the chamber, stock design, and bolt-handle shape. A heavy-barrel rifle often requires more clearance than a sporter-barrel version. Stocks with a raised comb may also work better with a slightly higher optic than a traditional low-comb hunting stock.

Match Ring Height to the Scope

The objective bell is usually the limiting factor. Measure the scope’s outside objective diameter rather than relying on the stated optical size. A scope advertised as having a 50 mm objective may have a larger external bell once its housing is included. Add a safety margin so the bell does not touch the barrel under recoil or temperature changes.

The scope’s eyepiece and magnification ring also need room around the bolt handle and receiver. On some Model 700 setups, the ocular housing can interfere with bolt operation even when the objective clears the barrel. Place the optic in the rings without fully tightening them, then check whether the bolt can open and close freely through its complete travel.

The following ranges are general starting points, not universal prescriptions. They assume conventional one-inch or 30 mm scope tubes and should be checked against the actual ring manufacturer’s dimensions.

Scope configuration Typical starting point Main clearance concern
Compact scope with 32–40 mm objective Low Bolt handle and receiver clearance
Hunting scope with 40–44 mm objective Low to medium Objective bell over the barrel
Scope with 50 mm objective Medium to high Barrel, base, and objective clearance
Large tactical or long-range optic Medium to high Rail height, bolt travel, and cheek weld
Extended-eye-relief or specialized optic Varies widely Eye relief and mounting position

Measure the gap between the objective bell and barrel after the scope is positioned. A small visible gap is necessary, but excessive height is undesirable because it can make the rifle harder to control and may require a higher cheek rest.

Prioritize Eye Alignment and Cheek Weld

A properly mounted scope should allow you to establish a full, clear sight picture without lifting your head or stretching your neck. With the rifle shouldered naturally and your eyes closed, settle into your normal position. When you open your eyes, your view through the optic should be close to centered. If you must move your head significantly, the scope may be too high, too low, or positioned incorrectly for its eye relief.

Cheek weld is especially important on a hunting rifle. A consistent cheek position helps you return to the same sight picture and can make field shooting more controlled. If the optic is mounted too high, your cheek may float above the stock, causing inconsistent alignment. If it is too low, the stock can press uncomfortably against your face or prevent a relaxed shooting position.

Eye relief should be set before final tightening. Move the scope forward or backward until it provides a full image at the shooting position you actually use. A perfect height does not compensate for incorrect eye relief. Keep the optic level with the rifle and tighten the rings gradually according to the manufacturer’s torque specifications.

Check the Complete Mounting System

The correct height is determined by the entire system: receiver, base or rail, rings, scope, barrel, and stock. A thick Picatinny rail can raise the optic substantially compared with a low-profile two-piece base. Integral or lightweight bases may permit a lower installation, but only if they provide the correct footprint and alignment for your Model 700 variant.

Verify whether your rifle is a short-action or long-action model and select a compatible base. Although many Model 700 components share a familiar mounting pattern, action length, production differences, and aftermarket modifications can affect fit. Ring diameter must also match the scope tube, such as one inch or 30 mm.

A practical fitting method is to install the unloaded rifle in a stable position, place the base and lower rings on the receiver, and set the optic in place without tightening. Use modeling clay, a thin strip of card, or a purpose-made clearance gauge to estimate the space between the objective and barrel. Then cycle the bolt, operate the safety, and confirm that the magnification ring remains accessible.

Choose Height for the Rifle’s Purpose

A lightweight Model 700 hunting rifle usually benefits from a low and compact optic position. Lower mounting can preserve a natural stock weld, reduce snagging in the field, and keep the rifle’s center of gravity closer to the bore. This is useful when carrying the rifle over long distances or shooting from improvised rests.

A precision-oriented Model 700 may use a larger optic, a taller rail, and accessories such as a bubble level or night-vision-compatible attachment. In that case, medium or high rings may be necessary. The rifle should still permit a repeatable cheek position, whether that requires an adjustable cheek riser or a stock designed for a taller sight line.

Your ammunition choice also affects the final sight-in process. After mounting the scope, use ammunition appropriate for the rifle and confirm the load details before zeroing; this ammunition label guide explains the information commonly printed on boxes and cartridges. Different bullet weights and loads can change point of impact, so a scope height decision should be followed by a careful range confirmation.

Avoid Common Installation Mistakes

One frequent mistake is selecting rings based only on objective diameter. The base thickness, barrel contour, scope saddle, and bolt clearance can be equally important. Another is assuming that a visible gap means the setup is correct. The optic must also sit at a usable height for the shooter’s face and stock.

Avoid forcing the scope into position or using ring screws to pull misaligned parts together. Inspect the bases for a proper fit, clean the contact surfaces, and follow the mounting instructions supplied with the hardware. If the optic cannot be positioned level, centered, and clear of the rifle without excessive pressure, stop and reassess the components.

A qualified gunsmith can help when the Model 700 has an aftermarket stock, heavy barrel, detachable magazine system, custom bolt handle, or unusual rail. Professional assistance is also sensible if you are uncertain about torque values, action compatibility, or bore-and-scope alignment. For purchasing information and available Remington products, the Remington firearms catalog provides a starting point, while any transfer requirements should be reviewed with the chosen FFL dealer.

Final Checks Before Zeroing

Before heading to the range, confirm that every fastener is tightened to the component maker’s specification and that the scope remains level. Cycle the bolt repeatedly, check the safety, inspect the objective clearance, and verify that the ocular end does not interfere with normal operation. Examine the rifle from several angles while shouldered, not just on a bench.

Use these practical recommendations when choosing and installing the setup:

Once the scope is secure, begin zeroing at a controlled distance and make adjustments methodically. Record the ring model, scope position, ammunition, and confirmed zero so the setup can be reproduced if the optic is removed. Taking these steps gives your Remington Model 700 a stable, comfortable sighting system suited to its stock, barrel, and intended role.