How to Clean the Ejector on a Remington 1100
A clean ejector helps a Remington 1100 throw spent shells consistently and cycle reliably. Powder residue, unburnt propellant, oil mixed with dust, and small brass or plastic fragments can collect around the barrel extension and interfere with the ejector’s movement. Regular inspection is especially useful for a shotgun used in hunting, clay target shooting, or field work.
Before beginning, work in a well-lit, ventilated area with an uncluttered bench. Australian owners should also follow the storage, transport, and handling requirements that apply in their state or territory. A licensed firearm dealer or qualified gunsmith can provide advice specific to the local rules if you are uncertain about any step.
Make The Shotgun Safe
Point the Remington 1100 in a safe direction and place the safety on. Remove the magazine cap, barrel, and fore-end only after confirming that the chamber and magazine tube are empty. Open the action and visually and physically check the chamber, the carrier area, and the magazine tube. Keep all ammunition in another room while cleaning.
The 1100 is a gas-operated semi-automatic shotgun, so residue can appear in several areas at once. Cleaning the ejector while ammunition is present on the bench creates an unnecessary risk. Use safety glasses when brushing or using compressed air, and avoid directing solvent toward your eyes or skin.
For owners in Melbourne, Sydney, Brisbane, or other areas where firearms must be stored under strict state requirements, cleaning should take place only after the firearm has been removed from its approved storage in a lawful manner. Once the work is finished, return it to compliant storage promptly.
Find The Ejector And Its Spring
On a Remington 1100, the ejector is located in the barrel extension at the rear of the barrel. It contacts the rim of the fired cartridge as the bolt moves rearward, helping push the empty hull clear of the receiver. The ejector works with the extractor, which grips the cartridge rim and pulls the shell from the chamber.
Look for a small metal ejector surface and its surrounding recess. Depending on the shotgun’s age and configuration, the area may show dark carbon, a thin film of oil, or compacted debris. Do not mistake the extractor on the bolt for the ejector in the barrel extension. Both influence ejection, but they are cleaned and inspected as separate components.
The ejector is commonly secured in the barrel extension rather than intended for casual removal. If it appears loose, bent, cracked, or unusually worn, stop before attempting to drive out a retaining pin. A gunsmith should handle repairs to a damaged or loose ejector assembly.
Strip The Barrel For Access
With the shotgun unloaded, remove the barrel according to the owner’s manual. On a standard 1100, this generally involves taking off the fore-end and sliding the barrel forward from the receiver, although variations exist across models and production periods. Do not force a part that resists movement.
Place the barrel on a padded surface with the barrel extension facing upward. Wipe away loose dirt with a dry cloth before applying cleaner. A soft nylon brush, cotton swabs, wooden picks, and a lint-free patch are useful for this job. Avoid steel picks, screwdrivers, and abrasive tools that can scratch the locking or bearing surfaces.
A small amount of a firearm-safe solvent can loosen residue around the ejector recess. Apply it to a patch or swab rather than flooding the barrel extension. Excess liquid can migrate into areas where it attracts grit or affects lubrication.
Clean The Ejector Without Forcing It
Use a nylon brush to work around the ejector, its recess, and the adjacent barrel extension. Brush in short strokes, then wipe away the loosened residue. A wooden pick can lift compacted fouling from a corner, but it should never be used as a lever against the ejector itself.
If the ejector is spring-loaded or moves slightly under gentle finger pressure, check that it returns smoothly. Do not compress it aggressively, pry it sideways, or remove it simply to reach hidden dirt. A restricted ejector may need repeated applications of solvent and light brushing rather than force.
A can of compressed air may help remove loose particles after brushing. Use brief bursts and keep the nozzle at a sensible distance. Shop air can drive debris deeper into the mechanism, and excessive pressure may dislodge small components. Finish by wiping the area dry, then apply only a very light film of suitable gun oil to exposed metal.
| Area | Cleaning method | Avoid |
|---|---|---|
| Ejector face | Nylon brush and solvent-dampened swab | Prying or filing |
| Ejector recess | Wooden pick and lint-free patch | Steel tools and heavy scraping |
| Barrel extension | Dry cloth followed by light solvent wipe | Flooding with oil |
| Extractor contact area | Careful brush cleaning | Disassembling without guidance |
| Surrounding metal | Thin protective oil film | Leaving excess lubricant |
Check The Extractor And Bolt
Cleaning the ejector alone may not correct poor ejection. Inspect the extractor claw on the bolt for fouling, chips, or a weak-looking spring. The extractor must hold the empty shell rim securely while the ejector pushes the hull outward. A dirty chamber can create similar symptoms by making the hull difficult to withdraw.
Wipe the bolt face and extractor area with a solvent-dampened cloth or swab. Use a nylon brush for stubborn residue, then dry the parts thoroughly. Do not put oil inside the gas ports or apply a thick coating to the bolt face, because excess lubricant can collect powder residue during firing.
After cleaning, examine the chamber for rust, plastic fouling, or a rough ring near the chamber mouth. A proper chamber brush may be used according to the manufacturer’s instructions. If the shotgun has a persistent failure to eject, marks on fired hulls, or a bolt that does not travel normally, arrange a professional inspection.
For broader ammunition knowledge, the Core-Lokt bullet guide offers useful context about cartridge construction, although shotgun ejection problems should still be assessed from the firearm and its fired hulls.
Reassemble And Test Safely
Once the ejector area and barrel extension are dry, reinstall the barrel, fore-end, and magazine cap in the sequence specified for your model. Confirm that the barrel seats fully and that the fore-end is secure. Operate the action several times with the firearm still unloaded, observing whether the bolt moves smoothly.
A function check should remain limited and safe. Confirm that the safety operates correctly and that the trigger is not tested with live ammunition present. If you use inert training cartridges for a mechanical check, keep them clearly separated from live shells and inspect them for damage before use.
At a suitable approved range, test the shotgun with a small quantity of lawful, compatible ammunition. Australian shooters should use the ammunition type permitted by their licence and firearm classification, and should follow range rules. If shells still fail to eject, stop firing rather than repeatedly cycling the action in an attempt to overcome the fault.
Recognise When Service Is Needed
A loose ejector, damaged retaining pin, cracked barrel extension, broken spring, or deep pitting requires more than routine cleaning. Filing the ejector or stretching its spring can change the timing and geometry of the action. Such modifications may create a safety problem and can complicate future repairs.
Repeated stovepipe failures, empty shells remaining in the chamber, weak ejection, or damage to cartridge rims are signs worth documenting. Keep a note of the ammunition load, hull type, weather, cleaning products, and exact symptom. Clear photographs can help a qualified gunsmith identify whether the ejector, extractor, chamber, gas system, or ammunition is responsible.
If a replacement part is needed, verify the exact 1100 variant and have installation performed by a competent professional. Parts availability and transfer requirements can differ in the Australian market, so do not assume that an overseas listing can be imported or fitted without meeting applicable law.
Maintain A Practical Cleaning Routine
A light ejector inspection after each shooting session takes only a few minutes. Remove loose fouling, check that the ejector is not obstructed, wipe the barrel extension dry, and store the shotgun according to local requirements. A more thorough cleaning is appropriate after high-volume clay shooting, wet field conditions, or use with ammunition that leaves heavy residue.
Keep solvent, oil, patches, and brushes labelled and stored away from children and ammunition. Avoid mixing household cleaners with firearm products. A modest amount of the correct lubricant is generally preferable to a wet, oily action that attracts dust.
For questions about product availability, order matters, or retailer support, you can contact the team. If an accessory or maintenance item is delayed in transit, review the shipment delay guidance before taking further action.
Clean the ejector gently, verify the extractor and chamber, and stop when a fault points to a repair rather than routine maintenance. Keep your Remington 1100 unloaded during cleaning, use lawful storage and transport practices in Australia, and arrange professional service whenever a component appears damaged or loose.